RSL Speedwoofer 12S

RSL Speedwoofer 12S Introduction

Awesome bass! This thing is huge! I paid $1450 for this sub. • Frequency Response: • Reference Mode (anechoic): 16 Hz-200 Hz ± 3db (SEE GRAPH FOR VARIOUS DSP RESPONSES) • Woofer: • 12” 500+ watt rated woofer • 4 ohm nominal Impedance • Proprietary RSL Die-cast aluminum frame with dual spider integration • Klippel optimized linear magnet motor and matched suspension • High-Excursion FEA optimized design motor structure • Integral VC Heat Sink/Inductance Control Sleeve • 1008 low-carbon steel motor parts (T-yoke and field plate) • Premium grade dual-stacked ceramic magnets • Ultra-high Temp (>200° C), Multi-layer Copper Voice Coil • Dual-mirrored, High yield fatigue-resistant Nomex™ spiders • Integrated Dual Spider spacer clamp ring • Kevlar™ reinforced paper cone with full anodized aluminum dust cap • High durability NBR surround • High duty cycle periodically stitched flexible tinsel lead wire with strain relief features • Enclosure: • Scratch and fingerprint resistant textured matte finish • Front multi-segment LED display/indicator (Volume, Mute, & DSP MODE) • Display sleeps after ~10 sec. of inactivity • Rear-vented Compression Guide™ tuning with turbulent free slot port • Internal structural reinforcement (Side to side, front to back, and top cross-bracing) • ¾” thick MDF panels with dado reinforced joints plus corner bracing • Laminated 1” front woofer baffle • Internally optimized damping • Removable cloth grille • XDR Series Amplifier: • IR Remote Control (Power Toggle, Volume +-, Mute, DSP Mode direct select (Reference, Music, Movies, Boundary) • External 3.5mm IR input for wiring external IR sensor (eye) • 500 watts RMS < 1% THD • 1550 watts peak • Patent Pending HSS™ Heat Sink/Shield Technology for greater thermal efficiency and capacity • DSP Modes – Reference, Music, Movies, Boundary (Rear LED indicator matches front display) • Reference – Minimal EQ processing, “natural” response for ideal transient performance • Music – Shelved response for extension, but with good upper bass impact • Movies – Enhanced output between 25-35Hz to augment low frequency content at low levels • Boundary – “Neighbor friendly”…Reduced lower frequencies to limit rumble through walls • Integrated double-precision 56-bit, 50 MIPS DSP processor • Intelligent class D topology, >85% Efficiency • Signal to noise ratio: >85dB • Auto-ON Threshold: 3mV • Auto-OFF: ~20 minutes (no signal) • Stand-by power consumption: ~1 watt • Power Input: Selectable 110/230VAC 50-60Hz switch • Low EMI design, CE & C-Tick compliant • Gold-plated RCA Line level inputs and RCA High-pass signal outputs (high-pass is adjustable and can be bypassed) • Speaker level inputs (Gold-plated, 5-way binding posts) • Chassis ground screw • USB Power port, easily connect external AR-4 2.4GHz wireless receiver • Low Pass Crossover Frequency: 30-250 Hz variable (with integrated bypass switch) • Low Pass Crossover Slope: 24 db/oct. • High Pass RCA Output Crossover Frequency: 30-250 Hz variable (with integrated bypass switch) • High Pass RCA Output Crossover Slope: 24 db/oct. • Phase Control: 0 to 180 continuously variable • Power Input: 115V, 60Hz, 230V, 50/60Hz AC • Feet: Includes 4 rubber feet • Dimensions with Feet: H: 22 1/4” W: 18 7/8” D: 22 1/8” • Weight: 82 lbs. • Shipping Dimensions: H: 29” W: 25” D: 29” • Shipped Weight: ~106 lbs. • Fuse: 115V (T6.3AL/250V) – 230V (T3.15AL/250V)